-
FuelTech PS-150 Pressure Sensor (0-150 psi)Vendor: FuelTechDescription Typically used to monitor fuel, oil, and wastegate pressure. TECHNICAL DESCRIPTION Output: 0.5-4.5V Supply: 5V Range: 0-150 psi Thread size: 1/8" NPT Connector Pinout: A - Ground B - 5V C - Signal SPECS Performance Long Term Drift: 0.2% FS/YR (non-cumulative) Accuracy: 0.25%...
- From $119.00
-
$145.00 - From $119.00
- Unit price
- per
-
FuelTech Flex Fuel SensorVendor: FuelTechDescription Downloads Ethanol content is a basis for many functions in an engine. The ethanol content as a variable can be the difference between having optimised ignition timing, fuel injection and boost levels when tuning versus average output when not compensating for the variable....
- From $139.00
-
- From $139.00
- Unit price
- per
-
Hybrid Racing K-Series Swap Coolant Temp Sensor AdapterVendor: Hybrid RacingEasily adapt your coolant temp sensor for your K-Swap Easy installation and perfect fit. Outer Thread 3/8 BSPT Fits K20 & K24 intake manifolds Description Vehicle Fitment This useful fitting allows you to insert a factory B/D coolant temp sensor into the upper section...
- $24.99
-
- $24.99
- Unit price
- per
-
Blox Racing Throttle Position Sensor (TPS) - Honda B/D/F/H-SeriesVendor: Blox RacingThe throttle position sensor (TPS) is basically a potentiometer that provides a variable resistance dependent upon the position of the throttle. There are many different instances when one needs to be replaced. Consequently, in order to purchase a replacement your only options were to buy a brand new...
- $49.60
-
$62.00 - $49.60
- Unit price
- per
-
SpeedFactory Racing 4 Bar MAP Sensor for B/D/F/H and S2000 (1-43+PSI)Vendor: Speedfactory RacingSpeedFactory 4 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure sensor that...
- $119.69
-
- $119.69
- Unit price
- per
-
SpeedFactory Racing 4 Bar MAP Sensor for K Series (1-43+PSI)Vendor: Speedfactory RacingSpeedFactory 4 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure sensor that...
- $119.69
-
- $119.69
- Unit price
- per
-
SpeedFactory Racing 3 Bar MAP Sensor for B/D/F/H and 00-05 S2000 (1-29+PSI)Vendor: Speedfactory RacingSpeedFactory 3 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure sensor...
- $119.69
-
- $119.69
- Unit price
- per
-
SpeedFactory Racing 3 Bar MAP Sensor K Series - 06-09 S2000, 06-11 Civic R18, 12-15 Civic Si, 2013+ILX, 09-10 TSX, CRZ (1-29+PSI)Vendor: Speedfactory RacingSpeedFactory 3 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure...
- $119.69
-
- $119.69
- Unit price
- per
-
Innovate Extended Bung/Plug Kit (Stainless Steel) 1 inch TallVendor: Innovate MotorsportsAbout Product Additional Details About the Brand Innovate Extended Bung/Plug Kit (Stainless Steel) 1 inch TallThis increased depth 1" stainless steel weld fitting (bung) & plug kit for Innovate Motorsports wideband O2 sensors is an optional replacement for the parts included as standard with...
- $7.73
-
$11.23 - $7.73
- Unit price
- per
-
Innovate Extended Bung/Plug Kit (Mild Steel) 1 inch TallVendor: Innovate MotorsportsAbout Product Additional Details About the Brand Innovate Extended Bung/Plug Kit (Mild Steel) 1 inch Tall (Incl; with all AFR kits)This increased depth 1" mild steel weld fitting (bung) & plug kit for Innovate Motorsports wideband O2 sensors is a direct replacement for the...
- $7.73
-
$11.23 - $7.73
- Unit price
- per
-
Innovate Extended Bung/Plug Kit (Titanium) 1 inch TallVendor: Innovate MotorsportsAbout Product Additional Details About the Brand Innovate Extended Bung/Plug Kit (Titanium) 1 inch TallThis increased depth 1" titanium weld fitting (bung) & plug kit for Innovate Motorsports wideband O2 sensors is an optional replacement for the parts included as standard with Innovate Motorsports...
- $27.03
-
$39.31 - $27.03
- Unit price
- per
-
Innovate Extended Bung (Mild Steel) 1in TallVendor: Innovate MotorsportsAbout Product Additional Details About the Brand Innovate Extended Bung (Mild Steel) 1in TallThis increased depth 1" mild steel weld fitting (bung) only for Innovate Motorsports wideband O2 sensors is a direct replacement for the part included as standard with Innovate Motorsports products. Choose...
- $6.18
-
$8.99 - $6.18
- Unit price
- per
-
Innovate Ethanol Content Sensor (Continental)Vendor: Innovate MotorsportsAbout Product Additional Details About the Brand Innovate Ethanol Content Sensor (Continental)Ethanol Content Sensor Having a set of gauges in your car can be very critical, especially if you're one who likes to drive aggressively at the track. Keep an eye on the health...
- $91.92
-
$133.66 - $91.92
- Unit price
- per
-
Innovate 4 BAR MAP Sensor for MTX-D / SCG-1Vendor: Innovate MotorsportsAbout Product About the Brand Innovate 4 BAR MAP Sensor for MTX-D / SCG-1Innovate 4 BAR MAP Sensor for MTX-D / SCG-1 Having a set of gauges in your car can be very critical, especially if you're one who likes to drive aggressively at...
- $52.71
-
$76.65 - $52.71
- Unit price
- per
-
FuelTech Nano & NanoPRO LSU4.2 HarnessVendor: FuelTechCompatible with WB-O2 Nano and the new NanoPRO. For use with the Bosch LSU4.2 O2 sensor. Length: 2m (6.5ft) - Recommended size for most applications.1m (3ft)4.5m (15ft)
- From $60.00
-
- From $60.00
- Unit price
- per
-
FuelTech Shift Knob w/ Strain Gauge SensorVendor: FuelTechDescription Downloads Designed to use with FuelTech FT550/FT600 on board conditioner, to perform powershifts. Detects knob deformation to perform ignition cut/timing retard H-pattern, sequential or inline application CNC machined *Power shift functions: only compatible with dog engagement gearboxes (Liberty Pro-Shift, Liberty Face Plate, etc.)....
- $329.00
-
- $329.00
- Unit price
- per
-
FuelTech Remote Mount Pressure Sensor BlockVendor: FuelTechFuelTech's billet remote pressure sensor mounting block is the perfect solution to mount your pressure sensors in one common place, Each port is individually connected from top to bottom allowing you to run up to 4 separate pressure sensors on a small light weight...
- $75.00
-
- $75.00
- Unit price
- per
-
FuelTech Vacuum Distribution ManifoldVendor: FuelTechFuelTech's billet vacuum distribution manifold is the perfect solution for running and organizing all of the vacuum lines on your race car. With 7 vacuum ports (4 x 1/8 npt and 3 x 1/4 npt) there is plenty of room to run all of...
- $79.00
-
- $79.00
- Unit price
- per
-
FuelTech Travel SensorVendor: FuelTechThe best way of monitoring your vehicle`s suspension and body movements. Available travel lengths: 0-4", 0-8".Can be used with any FuelTech Power FT ECU. Technical Description 4" Travel Sensor: Total Travel: 4" Length Closed: 9" Length Extended: 13" Mounting: 5mm Heim joints Cable Length:...
- From $349.00
-
- From $349.00
- Unit price
- per
-
FuelTech External MAP Sensor, 10 BarVendor: FuelTechThis sensor is needed if you are exceeding the limit of your internal map sensor on your ECU or want to run an external map sensor on your setup. Reads up to 135.3 psi! Output: 0.5-4.5V Supply: 5V Range: -14.7 psi to +135.3 psi...
- From $175.00
-
- From $175.00
- Unit price
- per
Race Now Pay Later With Shop Pay Installments!
Trending Now
Racewerx Products
Vendor:
Racewerx
Using factory intake manifold bolts and studs, especially when paired with an aftermarket intake manifold or thermal gasket, can lead to issues like stripped or broken bolts and loose fastening, resulting in leaks. But our stud kit is here to simplify things. This kit...
- From $74.99
-
- From $74.99
- Unit price
- / per
Vendor:
Racewerx
Introducing the Racewerx Tucked K-Series Engine Harness — the pinnacle of engineering excellence for your K-series engine. Our Tucked K-Swap Engine Harness is meticulously designed as a high-quality replacement for the 02-04 RSX Type-S styled harness, offering a supremely clean aesthetic while compatible with...
- $448.99
-
$499.99 - $448.99
- Unit price
- / per
Vendor:
Racewerx
Introducing Racewerx Titanium Steering Wheel Bolts – the perfect blend of form and function for your vehicle's interior upgrade. Crafted from top-grade Titanium, these bolts offer a sleek and modern appearance that will instantly enhance your steering wheel's aesthetics. But it's not...
- $28.95
-
$34.99 - $28.95
- Unit price
- / per
Close
Sidebar
- Choosing a selection results in a full page refresh.